Franklin Electric 5800020610 Pumptec Motor Protection Device, 115/230V
Product Overview
The Franklin Electric 5800020610 Pumptec is a single-phase motor-protection device for selected 115V and 230V pump motors in the 1/3 to 1.5 HP range. It monitors motor load and incoming voltage so it can interrupt operation during qualifying dry-run, underload, overload, or voltage-related conditions. This helps keep a pump from continuing to run when the operating condition suggests loss of water, excessive load, or an electrical problem that could damage a compatible motor.
Pumptec is commonly used with submersible well pumps, surface pumps, irrigation pumps, and turf-water systems when the motor and installation fall within its supported range. The device responds after a listed three-second delay and can be configured for an automatic reset interval from 2 to 120 minutes. LED indicators help identify operating and fault conditions, while the alarm contact can support an external warning circuit. Proper setup still requires verification of horsepower, voltage, phase, wiring, motor amperage, load calibration, grounding, disconnects, and the specific pump application. It is a protection component, not a substitute for correct hydraulic sizing, motor overload protection, or required electrical safeguards.
The protection thresholds depend on correct installation and calibration. A dry well, blocked intake, broken shaft, closed valve, low line voltage, or overloaded pump can produce different load patterns, so fault indications should be investigated rather than repeatedly reset. Correcting the underlying hydraulic or electrical condition is necessary before returning the pump to normal service.
Key Features:
- Motor protection for selected 115V and 230V single-phase pump motors
- Dry-run and underload detection
- Overload and voltage-condition protection
- Automatic shutdown during qualifying fault conditions
- Adjustable automatic reset interval
- LED indicators for operation and troubleshooting
- Alarm contact for a compatible external warning circuit
Common Uses:
- Submersible well-pump motor protection
- Surface and jet-pump protection
- Irrigation and turf-pump systems
- Water systems where dry-run or abnormal-load monitoring is needed
Technical Specifications:
- Model: 5800020610
- Voltage: 115/230V
- Frequency: 50/60 Hz
- Phase: Single-phase
- Compatible Motor Range: Selected 1/3-1.5 HP motors
- Power Consumption: 4W
- Response Time: 3 seconds
- Reset Time: 2-120 minutes
- Protection Functions: Dry run, overload, underload, and voltage irregularities
- Alarm Contact Rating: 1A at 115/230V
Dimensions:
- Height: 8-13/32 in.
- Width: 4-13/16 in.
- Depth: 2-27/32 in.
Compatibility and Installation Notes:
Confirm that the motor horsepower, voltage, phase, full-load current, wiring, and pump application are supported before installation. Follow the Franklin Electric manual for mounting, conductor routing, calibration, reset timing, alarm wiring, fault interpretation, grounding, disconnects, and startup. The device should be installed by a qualified person familiar with pump controls and applicable electrical requirements.
FAQ:
What voltage does Pumptec support?
This model supports compatible 115V or 230V single-phase applications.
Does it provide dry-run protection?
Yes. It can shut down a compatible motor when the monitored load indicates a qualifying dry-run or underload condition.
What motor sizes are listed?
Selected motors from 1/3 to 1.5 HP, subject to the manufacturer compatibility and setup requirements.
Does it restart automatically?
It can use an adjustable automatic reset interval from 2 to 120 minutes when configured according to the manual.
Why Buy From Big Frog Supply?
Big Frog Supply provides clear product information, helpful support, and convenient online ordering for pump-protection equipment. Match the device to the motor and installation requirements before wiring or commissioning the system.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Franklin Electric 5800020610 Pumptec Motor Protection Device, 115/230V
Franklin Electric 5800020610 Pumptec Motor Protection Device, 115/230V
Product Overview
The Franklin Electric 5800020610 Pumptec is a single-phase motor-protection device for selected 115V and 230V pump motors in the 1/3 to 1.5 HP range. It monitors motor load and incoming voltage so it can interrupt operation during qualifying dry-run, underload, overload, or voltage-related conditions. This helps keep a pump from continuing to run when the operating condition suggests loss of water, excessive load, or an electrical problem that could damage a compatible motor.
Pumptec is commonly used with submersible well pumps, surface pumps, irrigation pumps, and turf-water systems when the motor and installation fall within its supported range. The device responds after a listed three-second delay and can be configured for an automatic reset interval from 2 to 120 minutes. LED indicators help identify operating and fault conditions, while the alarm contact can support an external warning circuit. Proper setup still requires verification of horsepower, voltage, phase, wiring, motor amperage, load calibration, grounding, disconnects, and the specific pump application. It is a protection component, not a substitute for correct hydraulic sizing, motor overload protection, or required electrical safeguards.
The protection thresholds depend on correct installation and calibration. A dry well, blocked intake, broken shaft, closed valve, low line voltage, or overloaded pump can produce different load patterns, so fault indications should be investigated rather than repeatedly reset. Correcting the underlying hydraulic or electrical condition is necessary before returning the pump to normal service.
Key Features:
- Motor protection for selected 115V and 230V single-phase pump motors
- Dry-run and underload detection
- Overload and voltage-condition protection
- Automatic shutdown during qualifying fault conditions
- Adjustable automatic reset interval
- LED indicators for operation and troubleshooting
- Alarm contact for a compatible external warning circuit
Common Uses:
- Submersible well-pump motor protection
- Surface and jet-pump protection
- Irrigation and turf-pump systems
- Water systems where dry-run or abnormal-load monitoring is needed
Technical Specifications:
- Model: 5800020610
- Voltage: 115/230V
- Frequency: 50/60 Hz
- Phase: Single-phase
- Compatible Motor Range: Selected 1/3-1.5 HP motors
- Power Consumption: 4W
- Response Time: 3 seconds
- Reset Time: 2-120 minutes
- Protection Functions: Dry run, overload, underload, and voltage irregularities
- Alarm Contact Rating: 1A at 115/230V
Dimensions:
- Height: 8-13/32 in.
- Width: 4-13/16 in.
- Depth: 2-27/32 in.
Compatibility and Installation Notes:
Confirm that the motor horsepower, voltage, phase, full-load current, wiring, and pump application are supported before installation. Follow the Franklin Electric manual for mounting, conductor routing, calibration, reset timing, alarm wiring, fault interpretation, grounding, disconnects, and startup. The device should be installed by a qualified person familiar with pump controls and applicable electrical requirements.
FAQ:
What voltage does Pumptec support?
This model supports compatible 115V or 230V single-phase applications.
Does it provide dry-run protection?
Yes. It can shut down a compatible motor when the monitored load indicates a qualifying dry-run or underload condition.
What motor sizes are listed?
Selected motors from 1/3 to 1.5 HP, subject to the manufacturer compatibility and setup requirements.
Does it restart automatically?
It can use an adjustable automatic reset interval from 2 to 120 minutes when configured according to the manual.
Why Buy From Big Frog Supply?
Big Frog Supply provides clear product information, helpful support, and convenient online ordering for pump-protection equipment. Match the device to the motor and installation requirements before wiring or commissioning the system.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Product Overview
The Franklin Electric 5800020610 Pumptec is a single-phase motor-protection device for selected 115V and 230V pump motors in the 1/3 to 1.5 HP range. It monitors motor load and incoming voltage so it can interrupt operation during qualifying dry-run, underload, overload, or voltage-related conditions. This helps keep a pump from continuing to run when the operating condition suggests loss of water, excessive load, or an electrical problem that could damage a compatible motor.
Pumptec is commonly used with submersible well pumps, surface pumps, irrigation pumps, and turf-water systems when the motor and installation fall within its supported range. The device responds after a listed three-second delay and can be configured for an automatic reset interval from 2 to 120 minutes. LED indicators help identify operating and fault conditions, while the alarm contact can support an external warning circuit. Proper setup still requires verification of horsepower, voltage, phase, wiring, motor amperage, load calibration, grounding, disconnects, and the specific pump application. It is a protection component, not a substitute for correct hydraulic sizing, motor overload protection, or required electrical safeguards.
The protection thresholds depend on correct installation and calibration. A dry well, blocked intake, broken shaft, closed valve, low line voltage, or overloaded pump can produce different load patterns, so fault indications should be investigated rather than repeatedly reset. Correcting the underlying hydraulic or electrical condition is necessary before returning the pump to normal service.
Key Features:
- Motor protection for selected 115V and 230V single-phase pump motors
- Dry-run and underload detection
- Overload and voltage-condition protection
- Automatic shutdown during qualifying fault conditions
- Adjustable automatic reset interval
- LED indicators for operation and troubleshooting
- Alarm contact for a compatible external warning circuit
Common Uses:
- Submersible well-pump motor protection
- Surface and jet-pump protection
- Irrigation and turf-pump systems
- Water systems where dry-run or abnormal-load monitoring is needed
Technical Specifications:
- Model: 5800020610
- Voltage: 115/230V
- Frequency: 50/60 Hz
- Phase: Single-phase
- Compatible Motor Range: Selected 1/3-1.5 HP motors
- Power Consumption: 4W
- Response Time: 3 seconds
- Reset Time: 2-120 minutes
- Protection Functions: Dry run, overload, underload, and voltage irregularities
- Alarm Contact Rating: 1A at 115/230V
Dimensions:
- Height: 8-13/32 in.
- Width: 4-13/16 in.
- Depth: 2-27/32 in.
Compatibility and Installation Notes:
Confirm that the motor horsepower, voltage, phase, full-load current, wiring, and pump application are supported before installation. Follow the Franklin Electric manual for mounting, conductor routing, calibration, reset timing, alarm wiring, fault interpretation, grounding, disconnects, and startup. The device should be installed by a qualified person familiar with pump controls and applicable electrical requirements.
FAQ:
What voltage does Pumptec support?
This model supports compatible 115V or 230V single-phase applications.
Does it provide dry-run protection?
Yes. It can shut down a compatible motor when the monitored load indicates a qualifying dry-run or underload condition.
What motor sizes are listed?
Selected motors from 1/3 to 1.5 HP, subject to the manufacturer compatibility and setup requirements.
Does it restart automatically?
It can use an adjustable automatic reset interval from 2 to 120 minutes when configured according to the manual.
Why Buy From Big Frog Supply?
Big Frog Supply provides clear product information, helpful support, and convenient online ordering for pump-protection equipment. Match the device to the motor and installation requirements before wiring or commissioning the system.
